Instruction Manual

Sun Master Series

Model GSCUF118/908/758

This page is the accessible web version of the printed instruction manual. It has the same instructions in the same order, and each diagram has a text description.

Components

Box contents
No.Part
1Frame
2Canopy
3Finial Cap
4Bottom Pole
Diagram: box contents, parts 1 to 4
Box contents, numbered 1 to 4. 1, Frame: the bare umbrella frame, closed, with the ribs folded along the pole and the crank handle near the bottom. 2, Canopy: the folded fabric canopy. 3, Finial Cap: a cylindrical cap with vertical ridges and a flared base. 4, Bottom Pole: a straight tube with one hole near the top.

Canopy Assembly

  1. Place the umbrella frame on a stable, elevated surface with the top of the frame extending over the edge.

    Diagram: placing the frame on a table with the top over the edge
    Left: the closed frame is laid across a table top, with two arrows pointing down. Right: the frame resting on the table with its top end extending past the table edge; an arrow points toward the top end.
  2. Unfold the canopy. Insert one arm underneath the canopy and locate the small opening at the center. Please note, the canopy should be inside out in this step.

    Diagram: reaching under the canopy to find the center opening
    Left: a person holds up the unfolded canopy and reaches one arm underneath it; a curved arrow shows the arm going under the canopy. Right: the person's hand, inside the canopy, comes up through the small opening at the center; an arrow points up.
  3. Use the same hand that is inside the canopy to grip the protruding thread at top of the frame. While maintaining the grip, use the other hand to flip the canopy over the frame.

    Diagram: gripping the top of the frame through the canopy and flipping the canopy over
    Left: a hand inside the canopy holds the canopy's center opening; an arrow points toward the threaded post protruding from the top of the frame. Right: the canopy's center opening is around the threaded post and a curved arrow shows the canopy being flipped over the frame.
  4. Adjust the small opening of the canopy until the threaded end is fully exposed. Screw the finial cap on clockwise to secure the canopy.

    Diagram: screwing the finial cap onto the top of the frame
    Left: the top of the frame covered by the canopy, with the threaded end showing through the canopy's center opening. Right: a hand screws the ridged finial cap onto the threaded end; a curved arrow shows the turning direction.
  5. Temporarily lift the assembled frame and canopy to allow the canopy to fully drape over the frame.

    Diagram: lifting the frame so the canopy drapes over it
    Left: the frame rests on the table edge with the canopy part-way over it; curved arrows show the canopy being flipped over the frame. An arrow points to the right-hand drawing, where the canopy hangs evenly over the frame with the cylindrical finial cap at the top.
  6. Locate the rib pockets at the bottom of the canopy. One at a time, pull each pocket down and insert the corresponding rib to complete the assembly. To remove the canopy, follow these steps in reverse order.

    Diagram: pulling a canopy rib pocket over the end of a rib
    Left: two hands pull one of the canopy's rib pockets along a rib, with two arrows pointing toward the rib tips at the lower end of the folded frame. Right: close-up of a rib tip and the canopy pocket; two arrows point to the pocket as it is fitted over the end of the rib.

Installation

Warning

  • Base is required for this umbrella and sold separately.
  • Umbrella should always be closed and secure with wind-tie in windy conditions
  1. Secure the umbrella bottom pole to a compatible base (sold separately).

    Diagram: securing the bottom pole in a base
    The bottom pole (one hole near the top) is lowered into the pole socket of a base, which is drawn in dashed lines; a down arrow shows the direction. A close-up shows the tightening knob on the base's pole socket, with two curved arrows showing the knob being turned.

    Shop umbrella bases

  2. Align the bottom portion of the frame to the opening of the bottom pole.

    Diagram for steps 2 to 4: pressing the push button and lowering the frame into the bottom pole until it clicks
    This drawing goes with steps 2, 3 and 4. The closed umbrella is held above the bottom pole, which stands in a base; a down arrow shows the frame being lowered into the pole. Upper close-up, labelled “PRESS”: a finger presses the metal push button near the bottom of the frame, with an arrow pointing into the tube. Lower close-up, labelled “CLICK”: the frame tube has slid down into the bottom pole (down arrow), and the push button has sprung out through the hole in the pole (arrow pointing outward).
  3. Locate the metal push button near the bottom of the frame. Press the button inward while inserting the frame into the bottom pole.

  4. Slowly rotate the frame to align the metal push button with the hole. Once there is a click, both parts are secured.

Operation

Opening and Closing

Opening

Turn the crank handle clockwise until the umbrella is fully open.

Diagram: turning the crank handle clockwise to open the umbrella
Left: the crank handle on the pole (the crank housing has ridged collars above and below it), with a circular arrow labelled “Clockwise”. Right: the umbrella open, with dashed arrows at the canopy edges pointing up and outward.

Closing

Turn the crank handle counterclockwise until the umbrella is fully closed, please operate slowly to avoid injury.

Diagram: turning the crank handle counterclockwise to close the umbrella
Left: the crank handle on the pole (the crank housing has ridged collars above and below it), with a circular arrow labelled “Counter Clockwise”. Right: the umbrella closed, with dashed arrows at the canopy edges pointing inward toward the pole.

Tilting

Engage Tilt

With the umbrella fully open, twist the collar above the crank handle clockwise to engage the tilt.

Diagram: twisting the collar above the crank handle clockwise to tilt the umbrella
Left: an arrow wraps around the ridged collar above the crank handle, labelled “Clockwise”, with its arrowhead pointing to the left across the front of the collar. Right: the open umbrella tilted to one side, with a dashed arrow at the raised side of the canopy pointing up.

Disengage Tilt

Twist the collar above the crank handle counterclockwise to return umbrella to its upright position.

Diagram: twisting the collar counterclockwise to return the umbrella upright
Left: an arrow wraps around the ridged collar above the crank handle, labelled “Counter Clockwise”, with its arrowhead pointing to the right across the front of the collar. Right: the open umbrella upright, with a dashed arrow at one side of the canopy pointing down.

Care & Maintenance

Care Tips

  • Use an appropriate base or anchoring system to secure the umbrella. Verify the recommended base weight for the item.
  • Base and umbrella are meant to lay on a flat surface.
  • Always move the umbrella by uninstalling and lifting/placing in desired area.
  • Add a fabric defense to your umbrella canopy for an added layer of protection against oil and water-based stains. Visit our website to purchase a bottle of Pacifica Preserve and Protect Fabric Defense.

General Warnings

  • The appropriate base or anchoring system is needed to provide stability for the umbrella. Please verify the recommended base weight for the item.
  • May cause damage or injury when used improperly.
  • Not meant for commercial use.
  • Not meant for use in windy or inclement weather conditions.
  • When not in use, cover and store outdoor furniture in a dry and clean area.
  • Do not use harsh cleaning products on the surface of your frame or canopy.

How to Clean

  • Frame
    • To keep the umbrella frame looking new, wipe the frame with a clean damp cloth and a solution of mild soap and water¹. Dry with a clean dry cloth. While canopy is installed, use a soft bristle brush to regularly remove any loose dirt, leaves, and other debris from fabric.
    • To remove water spots, use a clean cloth or soft bristle brush to scrub the frame with a solution of white vinegar and water². Dry with a clean dry cloth.
  • Canopy
    • While canopy is installed, use a soft bristle brush to regularly remove any loose dirt, leaves, or other debris from the fabric.
    • For spills and stains, spray a mild cleaning solution of mild soap and water¹ and scrub with a soft bristle brush or a clean cloth.
    • For more severe cases, purchase the Pacifica: Restore and Renew Fabric Cleaner. Spray the canvas 10 inches way from the surface, use a soft bristle brush to scrub the fabric. Thoroughly remove any residue with clean water.
    • Machine Wash Cold and Air Dry Only.
  • Cleaning Solution
    • Mild Soap and Water: ¼ cup mild soap : 1 gallon water
    • White Vinegar and Water: 1 cup vinegar : 1 cup water

Warranty

Overview

California Umbrella’s limited warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

This limited warranty can also be found at www.californiaumbrella.com/en/terms-of-sales#warranty and in the documentation we provide with the products.

We warrant that during the warranty period, the individual components of the products purchased from the site will be free from defects in materials and workmanship.

We limit the duration and remedies of all implied warranties, including without limitation the warranties of merchantability and fitness for a particular purpose, to the duration of this limited warranty. Our responsibility for defective products is limited to repair, replacement or refund as set forth in this warranty statement. Neither any performance or other conduct, nor any oral or written information, statement or advice provided by us, our agents, or employees will create a warranty, or in any way increase the scope or duration of this limited warranty.

Frames

  • Aluminum frames: 1-year limited warranty
  • Fiberglass Ribs: 3-year limited warranty
  • If a residential grade umbrella is used for commercial purposes, the warranty is reduced to 90 days.

Canopies

  • All canopies: 1-year limited workmanship warranty
  • Olefin fabric: 1-year limited warranty
  • Pacifica fabric : 4-year limited warranty
  • Sunbrella fabric : 5-year limited warranty
  • Sunbrella Awning fabric : 10-year limited warranty

Contact us through our ticketing system on californiaumbrella.com for warranty inquiries.

Questions about your product? Contact us or chat with us on californiaumbrella.com.

All product guides