Instruction Manual

Venture Series

Model ALTO118/908/758/604

This page is the accessible web version of the printed instruction manual. It has the same instructions in the same order, and each diagram has a text description.

Components

Box Contents
No.Part
1Frame
2Canopy
3Finial Cap
4Bottom Pole
Diagram: box contents
Box contents, numbered: 1 Frame, shown folded with the ribs closed; 2 Canopy, shown folded; 3 Finial Cap, a ball-shaped cap on a flat base; 4 Bottom Pole, a tube with a narrower upper section and one push button near its top.

Canopy Assembly

  1. Place the umbrella frame on a stable, elevated surface with the top of the frame extending over the edge.

    Diagram: resting the frame on a table edge
    Two drawings. Left: the folded frame is lowered (two downward arrows) onto a table so it rests across the table edge. Right: the frame is slid along the table (arrow pointing left) until the top of the frame, with its threaded hub top, extends past the table edge.
  2. Unfold the canopy. Insert one arm underneath the canopy and locate the small opening at the center. Please note, the canopy should be inside out in this step.

    Diagram: reaching under the canopy to find the center opening
    Two drawings of a person holding the unfolded canopy. Left: a curved arrow shows one arm reaching up underneath the canopy fabric. Right: the hand pushes up through the canopy and the fingertips emerge at the small center opening (arrow pointing up and to the right).
  3. Use the same hand that is inside the canopy to grip the protruding thread at top of the frame. While maintaining the grip, use the other hand to flip the canopy over the frame.

    Diagram: gripping the frame top and flipping the canopy over
    Two drawings. Left: the hand inside the canopy, with the center opening around the fingers, reaches toward the top of the frame (arrow pointing at the top of the frame, which shows the threaded hub top). Right: the canopy opening now sits on the top of the frame and a curved arrow shows the rest of the canopy being flipped over the frame.
  4. Adjust the small opening of the canopy until the threaded end is fully exposed. Screw the finial cap on clockwise to secure the canopy.

    Diagram: screwing the finial cap onto the threaded end
    Two drawings. Left: the canopy is gathered over the top of the frame with the threaded end showing through the small center opening. Right: a hand turns the finial cap (ball-shaped cap) onto the threaded end; a curved arrow shows the turning direction.
  5. Temporarily lift the assembled frame and canopy to allow the canopy to fully drape over the frame.

    Diagram: lifting the frame so the canopy drapes over it
    Two drawings, linked by an arrow pointing right. Left: the frame with the finial cap attached rests on the table edge while the canopy hangs over it; curved arrows show the frame being lifted and the canopy falling over the frame. Right: the canopy now drapes evenly along the length of the frame.
  6. Locate the rib pockets at the bottom of the canopy. One at a time, pull each pocket down and insert the corresponding rib to complete the assembly. To remove the canopy, follow these steps in reverse order.

    Diagram: fitting rib ends into the canopy rib pockets
    Two drawings. Left: hands pull a rib pocket at the edge of the canopy down the frame (two arrows pointing toward the rib ends) while the ends of the ribs are visible below. Right: close-up of a rib end being seated in a rib pocket; two arrows point to the pocket from above and below.

Installation

Warning

  • Base is required for this umbrella and sold separately.
  • Umbrella should always be closed and secure with wind-tie in windy conditions
  1. Secure the umbrella bottom pole to a compatible base (sold separately).

    Diagram: securing the bottom pole in a base
    The bottom pole is lowered (downward arrow) into the post of a square base drawn in dashed lines (base sold separately). A circular close-up shows the base post collar with a round knob on its side; curved arrows on both sides of the knob show it being turned to tighten.
  2. Align the bottom portion of the frame to the opening of the bottom pole.

  3. Locate the metal push button near the top of the bottom pole. Press the button inward while inserting the bottom pole into the frame.

  4. Slowly rotate the frame to align the metal push button with the hole. Once there is a click, both parts are secured.

    Diagram: joining the frame to the bottom pole with the push button
    One drawing covers Steps 2 to 4. The closed umbrella, canopy wrapped and tied, is lowered (downward arrow) onto the bottom pole standing in a square base. Upper close-up, labeled PRESS: a hand presses the metal push button near the top of the bottom pole inward (arrow pointing at the button). Lower close-up, labeled CLICK: the frame tube slides down over the bottom pole (downward arrow) and the push button pops out through the hole in the frame tube (arrow pointing outward).

Shop umbrella bases

Operation

Opening and Closing Umbrella (For 604/758/908)

Opening

Stand beneath the umbrella and locate the hub that connects the ribs. Firmly grip the hub and push it upward until it passes the first pin hole. Insert the connected pin into the hole to keep the canopy open. Please note, pin holes are meant to be used lowest to highest as fabric may stretch over time.

Diagram: pushing the hub up and inserting the pin
Two views looking up at the hub under the canopy. 1, Push Up: a hand grips the hub and pushes it upward (upward arrow). 2, Insert Pin: the pin, attached by a cord, is pushed sideways (arrow) into the pin hole in the pole just below the hub.

Closing

To close the canopy, firmly hold the hub to support its full weight, then pull the pin out of the hole. While keeping control of the hub, slowly lower it until the canopy is fully collapsed. To avoid injury, please operate slowly and carefully.

Diagram: holding the hub, pulling the pin and lowering slowly
Two views looking up at the hub. 1, Push Up & Hold: upward arrows under the hub. 2, Pull Pin: an arrow shows the pin pulled sideways out of the pole. 3, Lower Slowly: a hand grips the hub and a downward arrow shows it being lowered.

Opening and Closing Umbrella (For 118)

Opening

Loosen the ribs so they are free to move. Stand beneath or beside the umbrella and pull the pulley rope downward to raise the hub. Once fully open, maintain firm grip on the rope and insert the attached locking pin into the pin hole. Loop the remaining rope on the hook.

Diagram: opening the 118 with the pulley rope
Two views looking up at the hub. 1, Pull Down: hands pull the pulley rope downward (downward arrow) while a small arrow by the hub shows it rising. 2, Insert Pin: an arrow shows the locking pin pushed sideways into the pin hole below the hub. 3, Loop Rope: the remaining rope is coiled and hung on the hook.

Closing

Remove the pulley rope from the hook. Pull the rope downward slightly and remove the locking pin from the pin hole. Slowly release the pulley rope to lower the hub and collapse the canopy. To avoid injury, please operate slowly and carefully.

Diagram: closing the 118 by removing the pin and releasing the rope
Two views looking up at the hub, labels as printed. 1, Push Up & Hold: upward arrows under the hub, with the coiled rope hanging beside the pole. 2, Pull Pin: an arrow shows the locking pin pulled sideways out of the pole. 3, Rise Slowly: hands hold the rope with an upward arrow beside them, while a small arrow by the hub points down.

Care & Maintenance

Care Tips

  • Use an appropriate base or anchoring system to secure the umbrella. Verify the recommended base weight for your specific model. A minimum base weight of 70 lbs is required to maintain warranty coverage in commercial use case settings and environments.
  • Ensure the umbrella pole is fully and securely inserted into the base before use. Tighten any base tightening knobs to secure the umbrella. Confirm the canopy is correctly positioned and evenly seated on all frame ribs before opening.
  • For umbrellas with a pin-stop collar: start at the lowest pinhole for everyday functional use. As fabric naturally stretches over time, a higher pinhole can be used for a tighter, more aesthetic fit — however, a looser fitting is recommended in commercial & breezy conditions, as it allows the fabric to flex with the wind and improves long-term durability.
  • The base or anchor for the umbrella must rest on a flat, stable surface. Always move the umbrella by fully closing, uninstalling, and lifting/placing in the desired area — never drag or reposition while open.
  • You may add a fabric defense to your canopy for an added layer of protection against oil and water-based stains if desired. Visit our website to purchase a bottle of Pacifica Preserve and Protect Fabric Defense.

General Warnings

  • A minimum base weight of 70 lbs is required to maintain warranty coverage for anchor-related incidents. Always verify the recommended base weight for your specific umbrella model.
  • May cause damage or injury when used improperly.
  • Not meant for use in windy or inclement weather conditions. Always close and secure the umbrella before any high-wind event or storm.
  • When not in use, close the canopy, cover, and store outdoor furniture in a dry and clean area.
  • Do not use harsh cleaning products on the surface of your frame or canopy.

How to Clean

  • Frame
    • To keep the frame looking its best, wipe with a clean damp cloth and a solution of mild soap and water¹. Dry thoroughly with a clean dry cloth. While the canopy is installed, use a soft bristle brush to regularly remove loose dirt, leaves, and debris.
    • To remove water spots, scrub the frame with a clean cloth or soft bristle brush using a solution of white vinegar and water². Dry thoroughly with a clean dry cloth.
  • Canopy
    • While the canopy is installed, use a soft bristle brush to regularly remove loose dirt, leaves, and other debris from the fabric.
    • For spills and stains, spray a mild cleaning solution of mild soap and water¹ and scrub with a soft bristle brush or clean cloth.
    • For more severe cases, use Pacifica: Restore and Renew Fabric Cleaner. Spray 10 inches from the surface, scrub with a soft bristle brush, and thoroughly rinse with clean water.
    • Machine Wash Cold and Air Dry Only.
  • Cleaning Solution
    • Mild Soap and Water¹: ¼ cup mild soap : 1 gallon water
    • White Vinegar and Water²: 1 cup vinegar : 1 cup water

Warranty

Overview

California Umbrella’s limited warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

This limited warranty can also be found at www.californiaumbrella.com/en/terms-of-sales#warranty and in the documentation we provide with the products.

We warrant that during the warranty period, the individual components of the products purchased from the site will be free from defects in materials and workmanship.

We limit the duration and remedies of all implied warranties, including without limitation the warranties of merchantability and fitness for a particular purpose, to the duration of this limited warranty. Our responsibility for defective products is limited to repair, replacement or refund as set forth in this warranty statement. Neither any performance or other conduct, nor any oral or written information, statement or advice provided by us, our agents, or employees will create a warranty, or in any way increase the scope or duration of this limited warranty.

Frames

  • Aluminum frames: 1-year limited warranty
  • Fiberglass Ribs: 3-year limited warranty
  • If a residential grade umbrella is used for commercial purposes, the warranty is reduced to 90 days.

Canopies

  • All canopies: 1-year limited workmanship warranty
  • Olefin fabric: 1-year limited warranty
  • Pacifica fabric : 4-year limited warranty
  • Sunbrella fabric : 5-year limited warranty
  • Sunbrella Awning fabric : 10-year limited warranty

Contact us through our ticketing system on californiaumbrella.com for warranty inquiries.

Questions about your product? Contact us or chat with us on californiaumbrella.com.

All product guides